da wifinetwork » gio 4 lug 2013, 22:07
sembra che le vlan utilizzano il flash e saturano la cpu.
posto la configurazione:
/interface bridge
add admin-mac=00:00:00:00:00:00 ageing-time=5m arp=enabled auto-mac=yes \
disabled=no forward-delay=15s l2mtu=65535 max-message-age=20s mtu=1500 \
name=Loopbridge priority=0x8000 protocol-mode=none transmit-hold-count=6
add admin-mac=00:00:00:00:00:00 ageing-time=5m arp=enabled auto-mac=yes \
disabled=no forward-delay=15s l2mtu=65535 max-message-age=20s mtu=1500 \
name=bridge2 priority=0x8000 protocol-mode=none transmit-hold-count=6
add admin-mac=00:00:00:00:00:00 ageing-time=5m arp=enabled auto-mac=yes \
disabled=no forward-delay=15s l2mtu=1500 max-message-age=20s mtu=1500 \
name=bridge1 priority=0x8000 protocol-mode=none transmit-hold-count=6
/interface ethernet
set 0 arp=enabled auto-negotiation=yes disabled=no full-duplex=yes l2mtu=1600 \
mac-address=D4:CA:6D:2A:40:74 mtu=1500 name=ether10 speed=100Mbps
set 1 arp=enabled auto-negotiation=yes disabled=no full-duplex=yes l2mtu=1600 \
mac-address=D4:CA:6D:2A:40:75 mtu=1500 name=ether9_Torre_3 speed=100Mbps
set 2 arp=enabled auto-negotiation=yes disabled=no full-duplex=yes l2mtu=1600 \
mac-address=D4:CA:6D:2A:40:77 mtu=1500 name=ether7_Torre_1 speed=100Mbps
set 3 arp=enabled auto-negotiation=yes disabled=no full-duplex=yes l2mtu=1600 \
mac-address=D4:CA:6D:2A:40:76 mtu=1500 name=ether8_Torre_2 speed=100Mbps
set 4 arp=enabled auto-negotiation=yes disabled=no full-duplex=yes l2mtu=1600 \
mac-address=D4:CA:6D:2A:40:78 mtu=1500 name=ether6_Soc_Cava speed=100Mbps
set 5 arp=enabled auto-negotiation=yes bandwidth=unlimited/unlimited \
disabled=no full-duplex=yes l2mtu=1598 mac-address=D4:CA:6D:2A:40:79 \
master-port=none mtu=1500 name=ether5 speed=100Mbps
set 6 arp=enabled auto-negotiation=yes bandwidth=unlimited/unlimited \
disabled=no full-duplex=yes l2mtu=1598 mac-address=D4:CA:6D:2A:40:7A \
master-port=none mtu=1500 name="ETH4-Torre s.s.-1" speed=100Mbps
set 7 arp=enabled auto-negotiation=yes bandwidth=unlimited/unlimited \
disabled=no full-duplex=yes l2mtu=1598 mac-address=D4:CA:6D:2A:40:7B \
master-port=none mtu=1500 name=ETH3-Oria-2 speed=100Mbps
set 8 arp=enabled auto-negotiation=yes bandwidth=unlimited/unlimited \
disabled=no full-duplex=yes l2mtu=1598 mac-address=D4:CA:6D:2A:40:7C \
master-port=none mtu=1500 name=ETH2-Oria-1 speed=100Mbps
set 9 arp=enabled auto-negotiation=yes bandwidth=unlimited/unlimited \
disabled=no full-duplex=yes l2mtu=1598 mac-address=D4:CA:6D:2A:40:7D \
master-port=none mtu=1500 name=ETH1-Master speed=100Mbps
/interface vpls
add advertised-l2mtu=1500 arp=enabled cisco-style=no cisco-style-id=0 \
disable-running-check=no disabled=no l2mtu=1500 mac-address=\
02:42:73:3E:6C:C7 mtu=1500 name=VPLS-vs-ORIA-1 pw-type=raw-ethernet \
remote-peer=10.255.0.2 use-control-word=default vpls-id=1:1
add advertised-l2mtu=1500 arp=enabled cisco-style=no cisco-style-id=0 \
disable-running-check=no disabled=no l2mtu=1500 mac-address=\
02:42:73:3E:6C:C7 mtu=1500 name=VPLS-vs-ORIA-2 pw-type=raw-ethernet \
remote-peer=10.255.0.3 use-control-word=default vpls-id=1:1
add advertised-l2mtu=1500 arp=enabled cisco-style=no cisco-style-id=0 \
disable-running-check=no disabled=no l2mtu=1500 mac-address=\
02:42:73:3E:6C:C7 mtu=1500 name=VPLS-vs-SM pw-type=raw-ethernet \
remote-peer=10.255.0.4 use-control-word=default vpls-id=1:1
/interface vlan
add arp=enabled disabled=yes interface=bridge1 mtu=1500 name=VLAN-vs-NAS \
use-service-tag=no vlan-id=50
add arp=enabled disabled=yes interface=ETH2-Oria-1 mtu=1500 name=\
VLAN-vs-ORIA-1 use-service-tag=no vlan-id=10
add arp=enabled disabled=yes interface=ETH3-Oria-2 mtu=1500 name=\
VLAN-vs-ORIA-2 use-service-tag=no vlan-id=11
/interface ethernet switch
set 0 mirror-source=none mirror-target=none name=switch1
/ip ipsec proposal
set [ find default=yes ] auth-algorithms=sha1 disabled=no enc-algorithms=3des \
lifetime=30m name=default pfs-group=modp1024
/mpls traffic-eng tunnel-path
add disabled=no hops="" name=dynamic use-cspf=yes
add disabled=no hops=10.0.2.2:strict name=te-vs-oria2 use-cspf=no
add disabled=no hops=10.0.1.2:strict name=te-vs-oria1 use-cspf=no
add disabled=no hops=10.0.1.2:strict,10.0.3.1:strict,10.0.3.2:strict name=\
te-vs-sm use-cspf=no
/interface traffic-eng
add auto-bandwidth-avg-interval=5m auto-bandwidth-range=0bps \
auto-bandwidth-reserve=0% auto-bandwidth-update-interval=1h bandwidth=\
500kbps bandwidth-limit=disabled disable-running-check=no disabled=yes \
from-address=10.255.0.1 mtu=1500 name=TE-vs-ORIA1 primary-path=\
te-vs-oria1 primary-retry-interval=1m record-route=yes secondary-paths=\
dynamic to-address=10.255.0.2
add auto-bandwidth-avg-interval=5m auto-bandwidth-range=0bps \
auto-bandwidth-reserve=0% auto-bandwidth-update-interval=1h bandwidth=\
500kbps bandwidth-limit=disabled disable-running-check=no disabled=yes \
from-address=10.255.0.1 mtu=1500 name=TE-vs-ORIA2 primary-path=\
te-vs-oria2 primary-retry-interval=1m record-route=yes secondary-paths=\
dynamic to-address=10.255.0.3
add auto-bandwidth-avg-interval=5m auto-bandwidth-range=0bps \
auto-bandwidth-reserve=0% auto-bandwidth-update-interval=1h bandwidth=\
1Mbps bandwidth-limit=disabled disable-running-check=no disabled=yes \
from-address=10.255.0.1 mtu=1500 name=TE-vs-SM primary-path=te-vs-sm \
primary-retry-interval=1m record-route=no secondary-paths=dynamic \
to-address=10.255.0.4
/port
set 0 baud-rate=115200 data-bits=8 flow-control=none name=serial0 parity=none \
stop-bits=1
set 1 baud-rate=115200 data-bits=8 flow-control=none name=serial1 parity=none \
stop-bits=1
/ppp profile
set 0 change-tcp-mss=yes name=default only-one=default use-compression=\
default use-encryption=default use-mpls=default use-vj-compression=\
default
set 1 change-tcp-mss=yes name=default-encryption only-one=default \
use-compression=default use-encryption=yes use-mpls=default \
use-vj-compression=default
/interface pppoe-client
add ac-name="" add-default-route=no allow=pap,chap,mschap1,mschap2 \
dial-on-demand=no disabled=no interface=bridge1 max-mru=1480 max-mtu=1480 \
mrru=disabled name=pppoe-out1 password=sw1 profile=default service-name=\
"" use-peer-dns=no user=switch_torre_1
/queue type
set 0 kind=pfifo name=default pfifo-limit=50
set 1 kind=pfifo name=ethernet-default pfifo-limit=50
set 2 kind=sfq name=wireless-default sfq-allot=1514 sfq-perturb=5
set 3 kind=red name=synchronous-default red-avg-packet=1000 red-burst=20 \
red-limit=60 red-max-threshold=50 red-min-threshold=10
set 4 kind=sfq name=hotspot-default sfq-allot=1514 sfq-perturb=5
set 5 kind=none name=only-hardware-queue
set 6 kind=mq-pfifo mq-pfifo-limit=50 name=multi-queue-ethernet-default
set 7 kind=pfifo name=default-small pfifo-limit=10
/routing bgp instance
set default as=65530 client-to-client-reflection=yes disabled=no \
ignore-as-path-len=no name=default out-filter="" redistribute-connected=\
no redistribute-ospf=no redistribute-other-bgp=no redistribute-rip=no \
redistribute-static=no router-id=0.0.0.0 routing-table=""
/snmp community
set [ find default=yes ] addresses=0.0.0.0/0 authentication-password="" \
authentication-protocol=MD5 encryption-password="" encryption-protocol=\
DES name=public read-access=yes security=none write-access=no
/system logging action
set 0 memory-lines=100 memory-stop-on-full=no name=memory target=memory
set 1 disk-file-count=2 disk-file-name=log disk-lines-per-file=100 \
disk-stop-on-full=no name=disk target=disk
set 2 name=echo remember=yes target=echo
set 3 bsd-syslog=no name=remote remote-port=514 src-address=0.0.0.0 \
syslog-facility=daemon syslog-severity=auto target=remote
/user group
set read name=read policy="local,telnet,ssh,reboot,read,test,winbox,password,w\
eb,sniff,sensitive,api,!ftp,!write,!policy" skin=default
set write name=write policy="local,telnet,ssh,reboot,read,write,test,winbox,pa\
ssword,web,sniff,sensitive,api,!ftp,!policy" skin=default
set full name=full policy="local,telnet,ssh,ftp,reboot,read,write,policy,test,\
winbox,password,web,sniff,sensitive,api" skin=default
/interface bridge port
add bridge=bridge1 disabled=no edge=auto external-fdb=auto horizon=none \
interface=VPLS-vs-ORIA-1 path-cost=10 point-to-point=auto priority=0x80
add bridge=bridge1 disabled=no edge=auto external-fdb=auto horizon=none \
interface=VPLS-vs-ORIA-2 path-cost=10 point-to-point=auto priority=0x80
add bridge=bridge1 disabled=no edge=auto external-fdb=auto horizon=none \
interface=VPLS-vs-SM path-cost=10 point-to-point=auto priority=0x80
add bridge=bridge1 disabled=no edge=auto external-fdb=auto horizon=none \
interface=ETH1-Master path-cost=10 point-to-point=auto priority=0x80
add bridge=bridge1 disabled=yes edge=auto external-fdb=auto horizon=none \
interface="ETH4-Torre s.s.-1" path-cost=10 point-to-point=auto priority=\
0x80
add bridge=bridge2 disabled=no edge=auto external-fdb=auto horizon=none \
interface=VLAN-vs-NAS path-cost=10 point-to-point=auto priority=0x80
add bridge=bridge2 disabled=no edge=auto external-fdb=auto horizon=none \
interface=VLAN-vs-ORIA-1 path-cost=10 point-to-point=auto priority=0x80
add bridge=bridge2 disabled=no edge=auto external-fdb=auto horizon=none \
interface=VLAN-vs-ORIA-2 path-cost=10 point-to-point=auto priority=0x80
add bridge=bridge1 disabled=no edge=auto external-fdb=auto horizon=none \
interface=ether6_Soc_Cava path-cost=10 point-to-point=auto priority=0x80
add bridge=bridge1 disabled=yes edge=auto external-fdb=auto horizon=none \
interface=ETH2-Oria-1 path-cost=10 point-to-point=auto priority=0x80
add bridge=bridge1 disabled=yes edge=auto external-fdb=auto horizon=none \
interface=ETH3-Oria-2 path-cost=10 point-to-point=auto priority=0x80
add bridge=bridge1 disabled=no edge=auto external-fdb=auto horizon=none \
interface=ether7_Torre_1 path-cost=10 point-to-point=auto priority=0x80
add bridge=bridge1 disabled=no edge=auto external-fdb=auto horizon=none \
interface=ether8_Torre_2 path-cost=10 point-to-point=auto priority=0x80
add bridge=bridge1 disabled=no edge=auto external-fdb=auto horizon=none \
interface=ether9_Torre_3 path-cost=10 point-to-point=auto priority=0x80
add bridge=bridge1 disabled=no edge=auto external-fdb=auto horizon=none \
interface=ether10 path-cost=10 point-to-point=auto priority=0x80
/interface bridge settings
set use-ip-firewall=no use-ip-firewall-for-pppoe=no use-ip-firewall-for-vlan=\
no
/interface ethernet switch port
set 0 vlan-header=leave-as-is vlan-mode=fallback
set 1 vlan-header=leave-as-is vlan-mode=fallback
set 2 vlan-header=leave-as-is vlan-mode=fallback
set 3 vlan-header=leave-as-is vlan-mode=fallback
set 4 vlan-header=leave-as-is vlan-mode=fallback
set 5 vlan-header=leave-as-is vlan-mode=fallback
/interface l2tp-server server
set authentication=pap,chap,mschap1,mschap2 default-profile=\
default-encryption enabled=no keepalive-timeout=30 max-mru=1460 max-mtu=\
1460 mrru=disabled
/interface ovpn-server server
set auth=sha1,md5 certificate=none cipher=blowfish128,aes128 default-profile=\
default enabled=no keepalive-timeout=60 mac-address=FE:7F:0D:AA:76:72 \
max-mtu=1500 mode=ip netmask=24 port=1194 require-client-certificate=no
/interface pptp-server server
set authentication=mschap1,mschap2 default-profile=default-encryption \
enabled=no keepalive-timeout=30 max-mru=1460 max-mtu=1460 mrru=disabled
/interface sstp-server server
set authentication=pap,chap,mschap1,mschap2 certificate=none default-profile=\
default enabled=no keepalive-timeout=60 max-mru=1500 max-mtu=1500 mrru=\
disabled port=443 verify-client-certificate=no
/ip accounting
set account-local-traffic=no enabled=no threshold=256
/ip accounting web-access
set accessible-via-web=no address=0.0.0.0/0
/ip address
add address=10.255.0.1/32 disabled=no interface=Loopbridge network=10.255.0.1
add address=10.0.1.1/30 disabled=no interface=ETH2-Oria-1 network=10.0.1.0
add address=10.0.2.1/30 disabled=no interface=ETH3-Oria-2 network=10.0.2.0
add address=172.16.0.2/24 disabled=no interface=bridge2 network=172.16.0.0
add address=10.10.1.1/30 disabled=no interface="ETH4-Torre s.s.-1" network=\
10.10.1.0
/ip dns
set allow-remote-requests=no cache-max-ttl=1w cache-size=2048KiB \
max-udp-packet-size=4096 servers=""
/ip firewall connection tracking
set enabled=yes generic-timeout=10m icmp-timeout=10s tcp-close-timeout=10s \
tcp-close-wait-timeout=10s tcp-established-timeout=1d \
tcp-fin-wait-timeout=10s tcp-last-ack-timeout=10s \
tcp-syn-received-timeout=5s tcp-syn-sent-timeout=5s tcp-syncookie=no \
tcp-time-wait-timeout=10s udp-stream-timeout=3m udp-timeout=10s
/ip firewall service-port
set ftp disabled=no ports=21
set tftp disabled=no ports=69
set irc disabled=no ports=6667
set h323 disabled=no
set sip disabled=no ports=5060,5061 sip-direct-media=yes
set pptp disabled=no
/ip neighbor discovery
set ether10 disabled=no
set ether9_Torre_3 disabled=no
set ether7_Torre_1 disabled=no
set ether8_Torre_2 disabled=no
set ether6_Soc_Cava disabled=no
set ether5 disabled=no
set "ETH4-Torre s.s.-1" disabled=no
set ETH3-Oria-2 disabled=no
set ETH2-Oria-1 disabled=no
set ETH1-Master disabled=no
set Loopbridge disabled=no
set bridge2 disabled=no
set bridge1 disabled=no
set pppoe-out1 disabled=yes
set TE-vs-ORIA1 disabled=yes
set TE-vs-ORIA2 disabled=yes
set TE-vs-SM disabled=yes
set VPLS-vs-ORIA-1 disabled=no
set VPLS-vs-ORIA-2 disabled=no
set VPLS-vs-SM disabled=no
set VLAN-vs-NAS disabled=yes
set VLAN-vs-ORIA-1 disabled=yes
set VLAN-vs-ORIA-2 disabled=yes
/ip proxy
set always-from-cache=no cache-administrator=webmaster cache-hit-dscp=4 \
cache-on-disk=no enabled=no max-cache-size=unlimited \
max-client-connections=600 max-fresh-time=3d max-server-connections=600 \
parent-proxy=0.0.0.0 parent-proxy-port=0 port=8080 serialize-connections=\
no src-address=0.0.0.0
/ip service
set telnet address="" disabled=no port=23
set ftp address="" disabled=yes port=21
set www address="" disabled=no port=80
set ssh address="" disabled=yes port=22
set www-ssl address="" certificate=none disabled=yes port=443
set api address="" disabled=yes port=8728
set winbox address="" disabled=no port=8291
/ip smb
set allow-guests=yes comment=MikrotikSMB domain=MSHOME enabled=no interfaces=\
all
/ip smb shares
set [ find default=yes ] comment="default share" directory=/pub disabled=no \
max-sessions=10 name=pub
/ip smb users
set [ find default=yes ] disabled=no name=guest password="" read-only=yes
/ip socks
set connection-idle-timeout=2m enabled=no max-connections=200 port=1080
/ip traffic-flow
set active-flow-timeout=30m cache-entries=4k enabled=no \
inactive-flow-timeout=15s interfaces=all
/ip upnp
set allow-disable-external-interface=yes enabled=no show-dummy-rule=yes
/mpls
set dynamic-label-range=16-1048575 propagate-ttl=yes
/mpls interface
set [ find default=yes ] disabled=no interface=all mpls-mtu=1508
/mpls ldp
set distribute-for-default-route=no enabled=yes hop-limit=255 loop-detect=no \
lsr-id=10.255.0.1 path-vector-limit=255 transport-address=10.255.0.1 \
use-explicit-null=no
/mpls traffic-eng interface
add bandwidth=10Mbps blockade-k-factor=3 disabled=no down-flood-thresholds="" \
igp-flood-period=3m interface=ETH2-Oria-1 k-factor=3 refresh-time=30s \
resource-class=0 te-metric=1 up-flood-thresholds="" use-udp=no
add bandwidth=10Mbps blockade-k-factor=3 disabled=no down-flood-thresholds="" \
igp-flood-period=3m interface=ETH3-Oria-2 k-factor=3 refresh-time=30s \
resource-class=0 te-metric=1 up-flood-thresholds="" use-udp=no
/port firmware
set directory=firmware ignore-directip-modem=no
/ppp aaa
set accounting=yes interim-update=0s use-radius=no
/queue interface
set ether10 queue=only-hardware-queue
set ether9_Torre_3 queue=only-hardware-queue
set ether7_Torre_1 queue=only-hardware-queue
set ether8_Torre_2 queue=only-hardware-queue
set ether6_Soc_Cava queue=only-hardware-queue
set ether5 queue=only-hardware-queue
set "ETH4-Torre s.s.-1" queue=only-hardware-queue
set ETH3-Oria-2 queue=only-hardware-queue
set ETH2-Oria-1 queue=only-hardware-queue
set ETH1-Master queue=only-hardware-queue
/radius incoming
set accept=no port=3799
/routing bfd interface
set [ find default=yes ] disabled=no interface=all interval=0.2s min-rx=0.2s \
multiplier=5
/routing mme
set bidirectional-timeout=2 gateway-class=none gateway-keepalive=1m \
gateway-selection=no-gateway origination-interval=5s preferred-gateway=\
0.0.0.0 timeout=1m ttl=50
/routing ospf area
set [ find default=yes ] area-id=0.0.0.0 disabled=no instance=default name=\
backbone type=default
/routing ospf instance
set [ find default=yes ] disabled=no distribute-default=never in-filter=\
ospf-in metric-bgp=auto metric-connected=20 metric-default=1 \
metric-other-ospf=auto metric-rip=20 metric-static=20 mpls-te-area=\
backbone mpls-te-router-id=Loopbridge name=default out-filter=ospf-out \
redistribute-bgp=no redistribute-connected=no redistribute-other-ospf=no \
redistribute-rip=no redistribute-static=no router-id=10.255.0.1
/routing ospf network
add area=backbone disabled=no network=10.0.1.0/30
add area=backbone disabled=no network=10.0.2.0/30
add area=backbone disabled=no network=10.255.0.1/32
/routing rip
set distribute-default=never garbage-timer=2m metric-bgp=1 metric-connected=1 \
metric-default=1 metric-ospf=1 metric-static=1 redistribute-bgp=no \
redistribute-connected=no redistribute-ospf=no redistribute-static=no \
routing-table=main timeout-timer=3m update-timer=30s
/snmp
set contact=info@gescomwifi.it enabled=yes engine-id="" location=\
switch_torre_1 trap-community=public trap-generators=start-trap \
trap-interfaces=all trap-target="" trap-version=1
/system clock
set time-zone-name=Europe/Rome
/system clock manual
set dst-delta=+00:00 dst-end="jan/01/1970 00:00:00" dst-start=\
"jan/01/1970 00:00:00" time-zone=+00:00
/system console
set [ find port=serial0 ] channel=0 disabled=no port=serial0 term=vt102
/system identity
set name=Switch_Torre_1
/system logging
set 0 action=memory disabled=no prefix="" topics=info
set 1 action=memory disabled=no prefix="" topics=error
set 2 action=memory disabled=no prefix="" topics=warning
set 3 action=echo disabled=no prefix="" topics=critical
add action=memory disabled=no prefix="" topics=write
/system note
set note="" show-at-login=yes
/system ntp client
set enabled=yes mode=unicast primary-ntp=213.154.229.24 secondary-ntp=0.0.0.0
/system resource irq
set 0 cpu=auto
set 1 cpu=auto
set 2 cpu=auto
set 3 cpu=auto
set 4 cpu=auto
set 5 cpu=auto
set 6 cpu=auto
set 7 cpu=auto
set 8 cpu=auto
set 9 cpu=auto
set 10 cpu=auto
set 11 cpu=auto
set 12 cpu=auto
set 13 cpu=auto
/system routerboard settings
set baud-rate=115200 boot-delay=2s boot-device=nand-if-fail-then-ethernet \
boot-protocol=bootp cpu-frequency=1GHz<400DDR> enable-jumper-reset=yes \
enter-setup-on=any-key force-backup-booter=no silent-boot=no
/system upgrade mirror
set check-interval=1d enabled=no primary-server=0.0.0.0 secondary-server=\
0.0.0.0 user=""
/system watchdog
set auto-send-supout=no automatic-supout=yes no-ping-delay=5m watch-address=\
none watchdog-timer=no
/tool bandwidth-server
set allocate-udp-ports-from=2000 authenticate=yes enabled=yes max-sessions=\
100
/tool e-mail
set address=0.0.0.0 from=<> password="" port=25 starttls=no user=""
/tool graphing
set page-refresh=300 store-every=5min
/tool graphing resource
add allow-address=0.0.0.0/0 disabled=no store-on-disk=yes
/tool mac-server
set [ find default=yes ] disabled=no interface=all
/tool mac-server mac-winbox
set [ find default=yes ] disabled=no interface=all
/tool mac-server ping
set enabled=yes
/tool sms
set allowed-number="" channel=0 keep-max-sms=0 receive-enabled=no secret=""
/tool sniffer
set file-limit=1000KiB file-name="" filter-ip-address="" filter-ip-protocol=\
"" filter-mac-address="" filter-mac-protocol="" filter-port="" \
filter-stream=yes interface=all memory-limit=100KiB memory-scroll=yes \
only-headers=no streaming-enabled=no streaming-server=0.0.0.0
/tool traffic-generator
set latency-distribution-scale=10 test-id=0
/user aaa
set accounting=yes default-group=read exclude-groups="" interim-update=0s \
use-radius=no
[/code]
