Intanto grazie mille della risposta!
per non essere troppo confuso, per ora posto la config della sezione "interface", spero possa essere sufficiente
- Codice: Seleziona tutto
# may/14/2011 19:17:23 by RouterOS 5.2
#
/interface ethernet
set 0 arp=enabled auto-negotiation=yes disabled=no full-duplex=yes l2mtu=1526 \
mac-address=00:0C:42:82:F2:C1 mtu=1500 name=ether1-gateway speed=100Mbps
set 1 arp=enabled auto-negotiation=yes bandwidth=unlimited/unlimited \
disabled=no full-duplex=yes l2mtu=1524 mac-address=00:0C:42:82:F2:C2 \
master-port=none mtu=1500 name=ether2-local-master speed=100Mbps
set 2 arp=enabled auto-negotiation=yes bandwidth=unlimited/unlimited \
disabled=no full-duplex=yes l2mtu=1524 mac-address=00:0C:42:82:F2:C3 \
master-port=ether2-local-master mtu=1500 name=ether3-local-slave speed=\
100Mbps
set 3 arp=enabled auto-negotiation=yes bandwidth=unlimited/unlimited \
disabled=no full-duplex=yes l2mtu=1524 mac-address=00:0C:42:82:F2:C4 \
master-port=ether2-local-master mtu=1500 name=ether4-local-slave speed=\
100Mbps
set 4 arp=enabled auto-negotiation=yes bandwidth=unlimited/unlimited \
disabled=no full-duplex=yes l2mtu=1524 mac-address=00:0C:42:82:F2:C5 \
master-port=ether2-local-master mtu=1500 name=ether5-local-slave speed=\
100Mbps
/interface pppoe-client
add ac-name="" add-default-route=yes allow=pap,chap,mschap1,mschap2 \
dial-on-demand=no disabled=no interface=ether2-local-master max-mru=1480 \
max-mtu=1480 mrru=disabled name=pppoe-out1 password=xxxxxx profile=\
default-encryption service-name=libero use-peer-dns=yes user=\
yyyyy@liberoflat
/interface ethernet switch
set switch1 mirror-source=none mirror-target=none name=switch1
/interface bridge settings
set use-ip-firewall=no use-ip-firewall-for-pppoe=no use-ip-firewall-for-vlan=\
no
/interface ethernet switch port
set ether2-local-master vlan-header=leave-as-is vlan-mode=fallback
set ether3-local-slave vlan-header=leave-as-is vlan-mode=fallback
set ether4-local-slave vlan-header=leave-as-is vlan-mode=fallback
set ether5-local-slave vlan-header=leave-as-is vlan-mode=fallback
set switch1_cpu vlan-header=leave-as-is vlan-mode=fallback
/interface l2tp-server server
set authentication=pap,chap,mschap1,mschap2 default-profile=\
default-encryption enabled=no max-mru=1460 max-mtu=1460 mrru=disabled
/interface ovpn-server server
set auth=sha1,md5 certificate=none cipher=blowfish128,aes128 default-profile=\
default enabled=no keepalive-timeout=60 mac-address=FE:43:3B:AF:6D:1B \
max-mtu=1500 mode=ip netmask=24 port=1194 require-client-certificate=no
/interface pptp-server server
set authentication=mschap1,mschap2 default-profile=default-encryption \
enabled=no keepalive-timeout=30 max-mru=1460 max-mtu=1460 mrru=disabled
/interface sstp-server server
set authentication=pap,chap,mschap1,mschap2 certificate=none default-profile=\
default enabled=no keepalive-timeout=60 max-mru=1500 max-mtu=1500 mrru=\
disabled port=443 verify-client-certificate=no
Ether1 non è in bridge o altro... non saprei...
in particolare aggiungo: se da ether1 eseguo uno scan mi trova il servizio PPPOEServer del router ADSL, anzi... ne trova due!! (qui fatto da ether2 ma anche da ether1 il risultato è uguale)
- Codice: Seleziona tutto
[admin@MikroTik] /interface pppoe-client> scan ether2-local-master
SERVICE MAC-ADDRESS AC-NAME
00:15:C6:95:56:CD SSG43
00:30:F2:74:F5:29 SSG33
Se servisse posso catturare e postare anche il log.
Grazie ancora
