ho da molto tempo un problema su praticamente tutte le Netmetal RB922 che ho comprato...non riesco a metterle a 20/40 MHz...se le imposto in quel modo il 90% delle volte succede che in una direzione portano un pò più banda (di certo non l'aumento che mi aspetterei), mentre nell'altra direzione non solo non aumenta la banda, ma anzi mi fa ogni tot di secondi un calo drastico tendente a 0.
E' capitato a qualcun altro?
La configurazione wireless di un'antenna:
- Codice: Seleziona tutto
/interface wireless security-profiles
set [ find default=yes ] supplicant-identity=MikroTik
add authentication-types=wpa2-psk eap-methods="" management-protection=allowed \
mode=dynamic-keys name=profile1 supplicant-identity="" wpa2-pre-shared-key=\
93400gjm0di03491kcmrtx323cv45g34
/interface wireless
set [ find default-name=wlan1 ] adaptive-noise-immunity=ap-and-client-mode \
band=5ghz-onlyn country=italy default-authentication=no disabled=no \
frequency=5900 frequency-mode=superchannel hide-ssid=yes ht-basic-mcs=mcs-0 \
ht-supported-mcs=mcs-0,mcs-1,mcs-2,mcs-3 mode=bridge nv2-preshared-key=\
RRmkE1cGjPWCApN_yeRPBtaTWbgDmfHcEBvyS_6j nv2-security=enabled radio-name=\
hl_hsd_to_hpg_2 rx-chains=0,1 scan-list=5900 security-profile=profile1 \
ssid=hsd-hpg-2 supported-rates-a/g=6Mbps tx-chains=0,1 wds-default-bridge=\
bridge1 wds-mode=dynamic wireless-protocol=nstreme
/interface wireless nstreme
set wlan1 disable-csma=yes enable-nstreme=yes framer-policy=best-fit
/interface wireless access-list
add interface=wlan1 mac-address=00:0C:42:D5:6D:AD vlan-mode=no-tag
/interface wireless connect-list
add interface=wlan1 mac-address=00:0C:42:D5:6D:AD security-profile=profile1
E la configurazione della sua station:
- Codice: Seleziona tutto
/interface wireless security-profiles
set [ find default=yes ] supplicant-identity=MikroTik
add authentication-types=wpa2-psk eap-methods="" management-protection=allowed \
mode=dynamic-keys name=profile1 supplicant-identity="" wpa2-pre-shared-key=\
93400gjm0di03491kcmrtx323cv45g34
/interface wireless
set [ find default-name=wlan1 ] adaptive-noise-immunity=ap-and-client-mode \
band=5ghz-onlyn country=italy default-authentication=no disabled=no \
frequency=5900 frequency-mode=superchannel ht-basic-mcs=mcs-0 \
ht-supported-mcs=mcs-0,mcs-1,mcs-2,mcs-3 mode=station-wds \
nv2-preshared-key=RRmkE1cGjPWCApN_yeRPBtaTWbgDmfHcEBvyS_6j nv2-security=\
enabled radio-name=hl_hpg_to_hsd_2 rx-chains=0,1 scan-list=5900 \
security-profile=profile1 ssid=hsd-hpg-2 supported-rates-a/g=6Mbps \
tx-chains=0,1 wds-default-bridge=bridge1 wds-mode=dynamic \
wireless-protocol=nstreme
/interface wireless nstreme
set wlan1 enable-nstreme=yes
/interface wireless access-list
add interface=wlan1 mac-address=E4:8D:8C:24:1F:92 vlan-mode=no-tag
/interface wireless connect-list
add interface=wlan1 mac-address=E4:8D:8C:24:1F:92 security-profile=profile1
